Concrete Slab Calculator

By Asira Tools Team · Last updated 20 November 2026

Work out the concrete volume and the rebar grid for a slab — yards, bags, and how many 20-foot bars to buy.

Advertisement

Concrete Slab Calculator

1.36 cubic yards
Slab area100 sq ft
Volume36.67 cu ft
80 lb bags62 bags
Rebar needed140 linear ft
20 ft rebar bars7 bars

Rebar is figured as a square grid at the spacing you choose, with bars running both directions. Bars are sold in 20-foot lengths; the bar count rounds up, and a little extra covers overlaps at the joints.

Formulas:

Volume (cu ft) = Length (ft) × Width (ft) × Thickness (in) ÷ 12, then add the waste percentage

Rebar (linear ft) = bars in each direction × slab dimension, where bars = floor(dimension in inches ÷ spacing) + 1

20 ft bars = Rebar (linear ft) ÷ 20, rounded up

What This Slab Calculator Does

A slab is the most common concrete project there is: patios, driveways, shed floors, garage floors, and sidewalks are all slabs. This calculator works out the two things you need to buy for one — the concrete itself and the steel reinforcement that goes inside it. Enter the length, width, and thickness, and you get the volume in cubic yards and cubic feet, the number of 80 lb bags if you are mixing by hand, and the rebar grid: how many linear feet of bar the slab needs and how many standard 20-foot bars that works out to.

The rebar figure is what sets this calculator apart from a plain volume calculation. Concrete is strong when squeezed but weak when pulled apart, and a slab is always being pulled: by the weight of what sits on it, by the ground shifting underneath, and by temperature changes that make it expand and contract. Steel reinforcement takes up those pulling forces. Without it, a slab cracks early and the cracks widen; with it, cracks stay hairline and the slab lasts decades.

How to Use the Calculator

Measure the slab in feet, length by width, and enter the thickness in inches. Four inches is the standard for a patio or walkway, 5 to 6 inches for a driveway. Set the waste allowance — 10% is the usual figure — and pick the rebar spacing. Eighteen inches on center is the common choice for a residential slab: close enough to control cracking, far enough apart to keep the steel bill reasonable. Twelve-inch spacing is for heavier loads, and 24-inch spacing suits light foot-traffic slabs.

The results update as you type, so you can compare options quickly. Try 4 inches versus 6 inches and watch the volume jump by half. Try 12-inch rebar spacing versus 18-inch and see the steel nearly double. That is the trade-off in slab design: thicker concrete and closer steel cost more up front and save you from an early replacement.

How the Rebar Grid Is Worked Out

The rebar in a slab is laid as a grid: one set of bars running along the length, another set running across the width, tied together where they cross. The number of bars in each direction depends on the spacing. For a 10-foot-wide slab with bars every 18 inches, there are 120 inches ÷ 18 = 6.67 spaces, which means 7 bars (you always need one more bar than the number of spaces). Each of those bars is 10 feet long, so that direction needs 70 linear feet of rebar. The other direction is identical on a square slab, giving 140 linear feet in total.

Rebar is sold in 20-foot lengths, so 140 linear feet becomes 7 bars. In practice you should buy one or two extra bars: bars are overlapped where they join — the overlap is typically 30 bar diameters, which for a #4 bar (half an inch thick) is about 15 inches — and there is always some cutting waste. The bar count in the results rounds up, but it does not add an overlap allowance, so treat it as the minimum.

Worked Example: A 10 × 10 Patio Slab

Take a patio slab 10 feet by 10 feet, 4 inches thick, with a 10% waste allowance and rebar at 18 inches on center. The volume is 10 × 10 × 4 ÷ 12 = 33.33 cubic feet before waste, and 33.33 × 1.10 = 36.67 cubic feet with waste. That is 36.67 ÷ 27 = 1.36 cubic yards. If you are mixing bags, you need 36.67 ÷ 0.6 = 62 bags at 80 lb each. The rebar grid needs 7 bars in each direction, 70 linear feet each way, 140 linear feet in total — which is 7 bars at 20 feet each.

For a bigger example, a 20 × 12 driveway slab at 6 inches thick with 5% waste and 12-inch rebar spacing needs 126 cubic feet, or 4.67 cubic yards — 210 bags at 80 lb, which is far beyond hand mixing and firmly in ready-mix territory. The rebar grid at 12-inch spacing needs 13 bars along the length (260 linear feet) and 21 bars across the width (252 linear feet), 512 linear feet in total, or 26 bars at 20 feet each. Compare that with the 10 × 10 patio: the driveway slab is 2.4 times the area but needs 3.7 times the rebar, because the spacing is tighter.

How Thick Should the Slab Be?

Thickness follows the load. A walkway or patio that only carries people is fine at 4 inches. A driveway for cars needs 5 to 6 inches. A garage floor that holds a truck, an RV pad, or a slab under heavy equipment should be 6 inches or more. Going thicker than you need wastes money — each extra inch on a 4-inch slab adds 25% more concrete — but going thinner than you need wastes the whole slab, because it will crack under load within a year or two.

Thickness and reinforcement work together. A 4-inch slab with rebar at 18 inches will outlast a 5-inch slab with no steel at all, because the steel is what holds a crack closed. For driveways, the usual specification is 5 to 6 inches thick with #4 rebar at 18 inches on center, or welded wire mesh as a cheaper alternative. Mesh is easier to lay but less effective than rebar, because it often ends up sitting on the ground instead of in the middle of the slab where it belongs.

Control Joints: Where the Cracks Go

Concrete shrinks as it cures, and it will crack somewhere — the only choice is whether the cracks appear where you want them. Control joints are shallow grooves cut or formed into the slab that give the concrete a planned weak point to crack along. The standard rule is to space joints 2 to 3 times the slab thickness in feet: for a 4-inch slab, that means joints every 8 to 12 feet. A 10 × 10 patio needs one joint each way, dividing it into four squares; a 20-foot driveway needs joints every 10 feet or so.

Joints should be cut to a quarter of the slab depth — 1 inch deep on a 4-inch slab — and cut within 24 hours of the pour, before the concrete has had time to crack on its own. Saw-cut joints look cleaner than tooled joints, but either works. Keep the panels as square as possible: long, narrow panels crack across the middle, so avoid any panel much longer than it is wide.

Tips for a Slab That Lasts

Prepare the base properly. A slab is only as good as what it sits on. Compact 4 inches of gravel under the slab, and make sure the ground is level and well drained. Soft spots under a slab become cracks in the slab.

Keep the rebar in the middle. Steel does no good sitting on the ground. Support the grid on chairs or dobies so it sits in the middle third of the slab — about 2 inches up in a 4-inch slab. This is the single most common reinforcement mistake.

Cure it slowly. Concrete gains strength by staying damp, not by drying out. Keep the surface moist for at least 7 days — cover it with plastic sheeting or wet burlap, or spray on a curing compound. Concrete that dries too fast ends up weak and dusty on the surface.

Do not add water to the mix. It is tempting to add water to make stiff concrete easier to work, but every extra gallon weakens the finished slab. If the mix is too stiff, the answer is a plasticizer admixture, not the hose.

Common Mistakes to Avoid

The biggest mistake is skipping the waste allowance. Forms bow outward under the weight of wet concrete, and the sub-base is never perfectly flat, so a slab calculated with zero waste will run short — and running short mid-pour leaves a cold joint. Ten percent is the standard; use 15% on rough ground.

The second mistake is measuring the thickness at the form and assuming it is the same everywhere. If the ground dips in the middle, the slab is thicker there and you need more concrete than the maths says. Measure the depth at several points and use the largest figure.

The third mistake is pouring on a hot, windy day without a curing plan. Rapid drying causes surface cracks called plastic shrinkage cracks, which appear within hours of the pour. If you must pour in hot weather, start early in the morning, have extra hands ready, and get the curing cover on as soon as the surface is finished.

Advertisement

Frequently Asked Questions

How much concrete do I need for a 10x10 slab 4 inches thick?

1.23 cubic yards before waste, or 1.36 cubic yards with a 10% waste allowance (36.67 cubic feet). In bags, that is 62 bags at 80 lb each.

How much rebar do I need for a 10x10 slab?

At 18-inch spacing, 140 linear feet of rebar, which is 7 bars at 20 feet each. That is 7 bars running each way, tied into a grid. Buy one extra bar to cover overlaps and cutting waste.

What rebar spacing should I use for a concrete slab?

18 inches on center is standard for a residential slab. Use 12-inch spacing for driveways and heavy loads, and 24-inch spacing only for light foot-traffic slabs such as walkways.

How thick should a concrete slab be for a driveway?

5 to 6 inches, with #4 rebar at 18 inches on center or welded wire mesh. A 4-inch slab is fine for patios and walkways but will crack under cars.

How far apart should control joints be in a concrete slab?

2 to 3 times the slab thickness in feet: every 8 to 12 feet for a 4-inch slab. Cut the joints 1 inch deep (a quarter of the slab depth) within 24 hours of the pour.