Roofing Cost Calculator
Estimate the cost of a new roof — by material, roof pitch, and whether the old roof comes off first.
Roofing Cost Calculator
Costs are typical installed averages (materials + labor) in US dollars, before permits. Enter amounts in your selected currency — no conversion is applied. One roofing square equals 100 sq ft. Actual quotes vary by region, roof complexity, and the number of layers to remove.
Formulas:
Roof area (sq ft) = House length (ft) × House width (ft) × Pitch factor (1.0 low, 1.1 medium, 1.25 steep)
Roofing squares = Roof area ÷ 100
New roof cost = Roof area × Installed rate per sq ft (asphalt $4.50, metal $10, tile $15)
Tear-off cost = Roof area × $1.50 per sq ft (if the old roof is removed)
What This Roofing Calculator Does
A new roof is one of the biggest single expenses a homeowner faces, and the price depends on three things: how big the roof is, how steep it is, and what it is made of. This calculator turns those three factors into a realistic installed cost — materials plus labor — for the three most common roofing materials: asphalt shingles, metal, and tile. It also adds the cost of tearing off the old roof, which is a separate line item many estimates bury in the total.
The roof area is worked out from the house footprint and the pitch. A flat roof has the same area as the house; a pitched roof has more, because the slope adds surface. A medium pitch (5/12 to 8/12) adds about 10% to the footprint area, and a steep pitch (9/12 and up) adds about 25%. Roofers measure in squares — one square is 100 square feet — so a 1,320 square foot roof is 13.2 squares, and materials are priced by the square.
How to Use the Calculator
Enter the length and width of the house in feet — the footprint, not the roof. The calculator applies the pitch factor to get the roof area. Then pick the pitch: low or flat for roofs up to 4/12 (rising 4 inches per foot of run), medium for 5/12 to 8/12, steep for 9/12 and up. If you are not sure of the pitch, measure it from inside the attic: mark 12 inches along a level held horizontally from the underside of the roof, then measure the vertical distance to the roof deck.
Choose the material, then decide whether the old roof comes off. Tear-off costs $1.50 per square foot and is almost always the right choice: it lets the roofer inspect the decking underneath, it avoids the extra weight of a second layer, and most manufacturers void the warranty if shingles are installed over an old roof. Roofing over is only sensible for a single layer of shingles in good condition on a tight budget.
Roofing Material Costs Compared
Asphalt shingles cost $4.50 per square foot installed and are the most common roofing material in North America by a wide margin. A standard architectural shingle roof lasts 20 to 30 years. Shingles are affordable, easy to install and repair, and available in many colors. Their weakness is lifespan: they wear out faster than any other material, and they are vulnerable to wind damage in storms.
Metal roofing costs $10 per square foot installed and lasts 40 to 70 years — two to three times as long as asphalt. Standing-seam metal is the premium option: concealed fasteners, clean lines, and excellent weather resistance. Metal reflects heat, which can cut cooling costs in hot climates, and it sheds snow well in cold ones. The downsides are the upfront cost and the noise in heavy rain, though insulation and solid decking reduce that considerably.
Tile roofing costs $15 per square foot installed and lasts 50 years or more — clay and concrete tile are among the longest-lived roofing materials made. Tile is heavy, though: a tile roof can weigh 600 to 1,000 lb per square, compared with 200 to 350 lb per square for asphalt, so the roof structure may need reinforcement. Tile is most common in warm, dry climates, where its weight and durability are an advantage and freeze-thaw damage is not a concern.
Worked Example: A 30 × 40 House
Take a house 30 feet long and 40 feet wide — a footprint of 1,200 square feet — with a medium-pitch roof and asphalt shingles, including a tear-off. The roof area is 1,200 × 1.1 = 1,320 square feet, which is 13.2 squares. The new roof costs 1,320 × $4.50 = $5,940. The tear-off costs 1,320 × $1.50 = $1,980. The total is $5,940 + $1,980 = $7,920.
For comparison, the same roof in metal would cost 1,320 × $10 = $13,200 plus the $1,980 tear-off, a total of $15,180 — nearly double the asphalt price, but with a lifespan two to three times as long. And a steep-pitch tile roof on a 40 by 30 foot house: the roof area is 1,200 × 1.25 = 1,500 square feet (15 squares), the tile costs 1,500 × $15 = $22,500, the tear-off is 1,500 × $1.50 = $2,250, and the total is $24,750. The steep pitch alone adds $3,750 to the tile cost compared with a flat roof of the same footprint.
What Else Affects Roof Cost?
Complexity is the biggest cost driver after material and pitch. A simple gable roof with two slopes is the cheapest to roof. Every valley, dormer, chimney, and skylight adds labor and flashing, and a cut-up roof with many features can cost 20 to 30% more per square foot than a simple one. The number of layers to tear off matters too: a roof with two old layers costs more to strip than one with a single layer.
Decking condition is the wild card. The roofer cannot see the roof deck until the old shingles come off, and rotten or damaged decking has to be replaced at $2 to $4 per square foot. On an old roof, budget an extra 10% for decking repairs — and ask the contractor how they price it before the work starts, so there are no surprises mid-job.
Access and location matter as well. A steep, high roof needs safety equipment and moves slower than a low, walkable one. Homes in remote areas pay more for material delivery and waste removal. And roofing prices rise after major storms, when demand surges and crews are booked out for months.
When Should You Replace a Roof?
The obvious signs are leaks, missing or curling shingles, and granules washing into the gutters — asphalt shingles shed their protective granules as they age, and a gutter full of granules means the shingles are near the end of their life. Less obvious signs are a sagging roof deck, daylight visible through the attic boards, and shingles that are 20 years old or more.
Age alone is a useful guide: an asphalt roof over 20 years old is living on borrowed time, even if it is not leaking yet. A metal roof at 40 years may still have decades left. The cost of waiting is real — a small leak that goes unnoticed can rot the decking and the rafters, turning a $8,000 roof job into a $15,000 roof and framing job. If the roof is near the end of its expected life and showing wear, replacing it before it fails is almost always cheaper than repairing the damage afterwards.
Tips for Hiring a Roofer
Get three written quotes. Roofing quotes vary widely, and the cheapest is not always the best. Compare the material brand and warranty, the underlayment type, and whether the quote includes tear-off, disposal, and permits. A quote that is much lower than the others usually means something has been left out.
Check the warranty. Shingles carry a manufacturer warranty of 25 to 50 years, but the warranty only covers defects, not installation errors — and it is often voided if the shingles are installed over an old roof or without proper ventilation. The contractor's workmanship warranty, typically 5 to 10 years, covers the installation itself. Get both in writing.
Ask about ventilation. A roof needs airflow through the attic to prevent moisture buildup and ice dams. A good roofer will check the existing ventilation and recommend ridge vents or soffit vents if it is inadequate. Poor ventilation shortens the life of the shingles and can void the warranty.
Never pay in full upfront. The standard arrangement is a deposit of 10 to 30%, with the balance due on completion. A contractor who demands full payment before starting is a red flag.
Common Mistakes to Avoid
The most common mistake is roofing over an old roof to save the tear-off cost. The saving is $1.50 per square foot — $1,980 on the example house — but the hidden costs are real: the extra weight stresses the structure, the old shingles telegraph their shape through the new ones, and most manufacturers void the warranty on a second layer. If the decking underneath is rotten, roofing over it hides the problem instead of fixing it.
The second mistake is choosing the cheapest shingle. Three-tab shingles cost less than architectural shingles, but they last about 15 to 20 years compared with 25 to 30, and they look flat and cheap. The price difference is roughly $1 per square foot — $1,320 on the example roof — which is a small premium for a roof that lasts half as long again.
The third mistake is ignoring the flashing. Flashing — the metal strips that seal the joints around chimneys, valleys, and walls — is where most roof leaks start. Reusing old flashing to save money is a false economy: new flashing costs a few hundred dollars and is the difference between a roof that stays dry and one that leaks in the first heavy rain.
Frequently Asked Questions
How much does a new roof cost for a 2,000 square foot house?
About $13,200 for asphalt shingles including tear-off. A 2,000 sq ft footprint with a medium pitch is 2,200 sq ft of roof (22 squares): 2,200 x $4.50 = $9,900 for the roof plus 2,200 x $1.50 = $3,300 for tear-off, a total of $13,200.
What is a roofing square?
One roofing square equals 100 square feet of roof area. Roofers price materials and labor by the square: a 1,320 sq ft roof is 13.2 squares. A bundle of asphalt shingles typically covers about one-third of a square.
How much does it cost to tear off an old roof?
About $1.50 per square foot, including removal and disposal. For a 1,320 sq ft roof that is $1,980. Roofs with two old layers, or with heavy materials like tile, cost more to remove.
How long does a metal roof last compared to asphalt?
A metal roof lasts 40 to 70 years, compared with 20 to 30 years for architectural asphalt shingles. Metal costs about $10 per square foot installed versus $4.50 for asphalt, but it typically needs replacing only once in a homeowner's lifetime.
Can I put a new roof over the old one?
Usually yes for one layer of asphalt shingles, but it is rarely the best choice. It saves the $1.50 per sq ft tear-off cost, but it adds weight, hides deck damage, and voids most manufacturer warranties. A tear-off lets the roofer inspect and repair the deck.