Drywall Calculator

By Asira Tools Team · Last updated 20 November 2026

Work out how many drywall sheets, screws, and buckets of joint compound a room needs — walls, ceiling, and waste included.

Advertisement

Drywall Calculator

17 sheets
Wall area352 sq ft
Ceiling area120 sq ft
Total area472 sq ft
Drywall screws544 screws
Joint compound (5-gal buckets)2 buckets

Based on standard 4x8 ft sheets (32 sq ft each), 32 screws per sheet, and one 5-gallon bucket of joint compound per 400 sq ft of taping and finishing. Openings are not subtracted: the extra sheets cover cuts around doors and windows.

Formulas:

Wall area (sq ft) = 2 × (Length + Width) × Height

Ceiling area (sq ft) = Length × Width (if included)

Sheets = Total area ÷ 32 sq ft per 4x8 sheet, plus the waste percentage, rounded up

Screws = Sheets × 32  ·  Joint compound buckets = Total area ÷ 400, rounded up (5-gallon buckets)

What This Drywall Calculator Does

Drywall — also called gypsum board or plasterboard — is sold in sheets, but rooms are measured in square feet, and the conversion between the two is where ordering mistakes happen. This calculator works out how many standard 4 by 8 foot sheets a room needs, how many screws to fasten them, and how many 5-gallon buckets of joint compound to tape and finish the joints. Enter the room size, say whether the ceiling is included, add a waste allowance, and the quantities appear.

A standard sheet is 4 feet wide and 8 feet long, which is 32 square feet. That is the size this calculator uses throughout. Longer sheets — 10 feet and 12 feet — exist and reduce the number of joints on long walls, but they are heavier, harder to handle, and harder to get into a house. For most residential rooms, 4 by 8 sheets are the practical choice, and they are what the calculator counts.

How to Use the Calculator

Measure the room in feet: length, width, and ceiling height. The wall area is the perimeter times the height — a 12 by 10 foot room with 8-foot ceilings has a perimeter of 44 feet and a wall area of 352 square feet. If the ceiling is included, its area is the floor area: 12 × 10 = 120 square feet. The calculator adds the two together and divides by 32 square feet per sheet.

Set the waste allowance last. Ten percent is the usual figure and covers the sheets cut around doors, windows, and outlets, plus the occasional broken sheet. Note that the calculator does not subtract doors and windows from the wall area — that is deliberate, because the extra sheets roughly cover the cutting waste around the openings. If your room has very large openings, such as a wall of windows, the sheet count will be slightly generous, which is the safe direction to err.

How Many Sheets per Room?

The answer depends on the room size and whether the ceiling is included. Here are common room sizes at 8-foot ceilings, walls and ceiling, before waste:

With a 10% waste allowance, the 12 by 10 room goes from 15 sheets to 17 sheets (472 × 1.10 = 519.2 square feet, divided by 32 = 16.23, rounded up to 17). The 10 by 10 room goes from 14 sheets to 15 sheets with waste. Always round up: a part sheet still has to be bought whole, and the offcuts are useful for patching and for small areas such as closet walls.

Worked Example: A 12 × 10 Bedroom

Take a bedroom 12 feet long, 10 feet wide, with 8-foot ceilings, ceiling included, and a 10% waste allowance. The wall area is 2 × (12 + 10) × 8 = 352 square feet. The ceiling area is 12 × 10 = 120 square feet. The total is 472 square feet. Dividing by 32 square feet per sheet gives 14.75 sheets before waste, and with 10% waste that becomes 472 × 1.10 ÷ 32 = 16.23 sheets, rounded up to 17 sheets. The screws needed are 17 × 32 = 544 screws. The joint compound needed is 472 ÷ 400 = 1.18 buckets, rounded up to 2 five-gallon buckets.

For a walls-only job, a 20 by 15 foot room with 9-foot ceilings and 5% waste: the wall area is 2 × (20 + 15) × 9 = 630 square feet, with no ceiling area. The sheets needed are 630 × 1.05 ÷ 32 = 20.67, rounded up to 21 sheets. The screws are 21 × 32 = 672, and the compound is 630 ÷ 400 = 1.58 buckets, rounded up to 2 buckets. Notice that the taller ceiling adds significantly to the wall area: the same room at 8 feet would need only 560 square feet of walls.

Screws, Tape, and Joint Compound

Each 4 by 8 sheet takes about 32 screws: screws are spaced 12 inches apart along the studs on walls, and 12 inches apart on ceilings, with extra screws along the edges. A 17-sheet room needs 544 screws, which is roughly one 1 lb box of coarse-thread drywall screws — a 1 lb box holds about 200 screws, so buy a 5 lb box (about 1,000 screws) and you will have plenty left over. Screws are cheap; running out mid-job is not worth saving a few dollars.

Joint compound — "mud" — is used to tape the joints between sheets and to cover the screw heads. A 5-gallon bucket covers about 400 square feet of taping and finishing for a standard three-coat job: a tape coat, a fill coat, and a finish coat. The 472 square foot bedroom above needs 2 buckets. You will also need joint tape — paper tape is the standard, and a 250-foot roll covers roughly 1,000 square feet of joints — and corner bead for the outside corners, which comes in 8-foot and 10-foot lengths.

Which Drywall Thickness?

Half-inch drywall is the standard for residential walls with studs 16 inches apart. It is light enough to handle easily — a 4 by 8 sheet weighs about 55 lb — and stiff enough to span the studs without sagging. Five-eighths inch drywall is used for ceilings, because it resists sagging between joists, and for fire-rated walls, where the extra thickness gives a one-hour fire rating.

Quarter-inch drywall is a specialty product used to cover existing walls without removing the old surface — it is flexible enough to bend around curves, which is why it is used on arched doorways. Moisture-resistant drywall, usually green or purple, is used in bathrooms and kitchens where humidity is high. It is not waterproof — it still needs tile or another waterproof layer in a shower — but it resists mould better than standard board.

Tips for Hanging Drywall

Hang the ceiling first, then the walls. The wall sheets support the edges of the ceiling sheets, which prevents sagging at the joints. Hang sheets horizontally on walls — the long edge runs along the studs — which puts the tapered edges together and makes taping easier.

Stagger the joints. Like brickwork, drywall joints should not line up in a continuous line. Offset the end joints by at least one stud bay from the sheet above or below. A continuous vertical joint is a weak line that will crack.

Leave a small gap at the floor. Drywall should sit about half an inch above the floor, not touching it. The gap is covered by the baseboard, and it keeps the bottom edge away from moisture on the floor. Use a scrap piece of drywall as a spacer while you fasten the sheet.

Do not overdrive the screws. A screw driven too deep breaks the paper face and loses its grip. The screw head should sit just below the surface, dimpling the paper slightly without tearing it. A drywall screw gun with a depth-setting nose makes this easy; a regular drill takes practice.

Common Mistakes to Avoid

The biggest mistake is under-ordering. Drywall is cheap — a sheet costs $10 to $15 — but a return trip to the store for one more sheet costs an hour of your time and may mean a different batch. Order the full quantity plus waste, and keep the spare sheets for patches.

The second mistake is hanging sheets vertically on walls. Vertical hanging puts the tapered edges against the studs, which makes the joints harder to tape and more visible. Horizontal hanging is the standard for a reason: the long tapered joints run along the middle of the wall, where they are easiest to finish.

The third mistake is rushing the finishing. Each coat of joint compound needs to dry fully — usually 24 hours — before the next coat goes on. Sanding between coats, using thin coats rather than thick ones, and keeping the knife clean are what separate a professional finish from a lumpy one. Three thin coats always look better than one thick coat.

Advertisement

Frequently Asked Questions

How many drywall sheets do I need for a 12x12 room?

17 sheets before waste, or 19 sheets with 10% waste, for walls and ceiling at 8-foot ceilings. The total area is 384 sq ft of walls plus 144 sq ft of ceiling = 528 sq ft, and 528 / 32 = 16.5 sheets, rounded up to 17.

How many screws are needed per sheet of drywall?

About 32 screws per 4x8 sheet, spaced 12 inches apart along the studs. A 17-sheet room needs about 544 screws. Buy a 5 lb box (about 1,000 screws) to have plenty of spares.

How much joint compound do I need?

About one 5-gallon bucket per 400 square feet of drywall for a three-coat tape and finish job. A 472 sq ft room needs 2 buckets. Buy one extra bucket if you are new to finishing, since beginners use more compound.

Should drywall be hung horizontally or vertically?

Horizontally on walls. The long tapered edges run along the middle of the wall, which makes the joints easier to tape and less visible. Vertical hanging is only used on short walls or where the studs are 24 inches apart.

What thickness drywall should I use?

1/2 inch is standard for residential walls with studs 16 inches apart. Use 5/8 inch for ceilings to resist sagging, and for fire-rated walls. Use moisture-resistant board in bathrooms and kitchens.